The Differences Between Non-curing Waterproof Coatings And Conventional Waterproof Coatings

Aug 20, 2025

Leave a message

1. Curing Characteristics: The core difference lies in whether full curing occurs

Non-curing waterproof coatings:
They remain in a paste-like or viscous liquid state at all times and do not fully cure into a solid film. They maintain viscosity and creep performance over the long term (similar to "never-drying asphalt paste"). Their molecular structure is stable and does not lose fluidity due to time or environmental changes.

Conventional waterproof coatings:
After construction, they cure into a solid film through chemical reactions (e.g., two-component polyurethane reactions) or physical volatilization (e.g., water evaporation in water-based coatings), forming a rigid or elastic continuous coating. Once cured, their state remains basically fixed.

2. Performance Differences: Flexibility, adhesion, and self-healing ability

Adhesion:
Due to their continuous viscosity, non-curing coatings can form "infiltrative adhesion" with substrates (concrete, membranes, etc.). Even if the substrate has slight cracks, they can still fit tightly and are less prone to lifting.
Conventional coatings have fixed adhesion after curing. If the substrate deforms or cracks, delamination or hollowing may occur.

Flexibility and crack resistance:
Non-curing coatings have high creep performance, enabling them to deform synchronously with the expansion, contraction, and settlement of the substrate. They can cover micro-cracks (even self-heal cracks less than 0.2mm).
Conventional coatings (especially rigid ones like cement-based permeable crystalline coatings) have poor flexibility, and coating cracking is likely to occur when the substrate deforms. Elastic coatings (e.g., polyurethane) have a certain degree of ductility but are far inferior to the "followability" of non-curing coatings.

Durability and weather resistance:
Since non-curing coatings do not cure, they have no risk of aging and cracking, and have better performance in resisting high and low temperatures (-30℃~80℃) and water scouring.
Conventional coatings (especially solvent-based ones) are prone to chalking and cracking when exposed to ultraviolet rays and temperature changes over time, with a relatively short service life (5-10 years vs. over 15 years for non-curing coatings).

3. Construction Methods: Different requirements for environment and craftsmanship

Non-curing waterproof coatings:
They need to be heated and melted (usually to 180-200℃) before brushing or spraying. Construction is greatly affected by temperature (insulation is required in low-temperature environments), and the material is viscous, requiring high standards for construction tools (e.g., special spray guns).
They are often used in combination with membranes (with non-curing coating as the adhesive layer) to form a "coating + membrane" dual waterproofing system.

Conventional waterproof coatings:
Construction is simpler. Most can be directly brushed (e.g., JS, acrylic) or applied after mixing (e.g., two-component polyurethane). No heating is required, and there are low requirements for ambient temperature (above 5℃ is sufficient) and tools. One-component coatings can even be rolled or scraped.

4. Applicable Scenarios: Targeted at solving different waterproofing needs

Non-curing waterproof coatings:
Suitable for scenarios with large substrate deformation and prone to cracking, such as roofs (especially accessible roofs, green roofs), basement floors/walls, tunnels, bridges, etc. They can cope with substrate changes caused by settlement and vibration.
Also suitable for renovation of old buildings (can directly cover the original waterproof layer without removal).

Conventional waterproof coatings:
Suitable for scenarios with stable substrates and high requirements for construction convenience, such as indoor areas like bathrooms, kitchens, balconies (mainly JS and acrylic), or external walls, light roofs (polyurethane, acrylic). They have lower costs and are suitable for large-area rapid construction.

Summary

Non-curing waterproof coatings are centered on "non-curing, high viscosity, and strong followability", focusing on long-term crack resistance and adaptation to complex substrates. Conventional waterproof coatings are characterized by "curing into a film and simple construction", suitable for conventional scenarios with stable substrates. The selection should be comprehensively judged based on the substrate condition, waterproofing life requirements, and construction conditions

Send Inquiry